75 HP, 1800 RPM, 208/230/460 Volts, TEFC, 365T, CRUSHER, PREMIUM, TECO, CDP0754

MAX-HT™ LOW VOLTAGE CRUSHER DUTY

AEHHGD, NEMA PREMIUM, DESIGN C (20 HP - 200 HP) [CDP]

APPLICATIONS:


• Crushers 
• Ball Mills/ Rolling Mills 
• Impactors 
• Any High Torque Application 
• Chippers/ Shredders

FEATURES:


• Output: 75 HP

• Speed: 1800 RPM

• Enclosure: Totally Enclosed Fan Cooled (IP55)

• Voltage: 208/230/460 Volts

• Frame: 365T

• Efficiency: 95.4% Full Load

• Power Factor: 86.5% Full Load

• Amperage: 85A Full Load

• Service Factor: Three Phase 60 Hz 1.15 Service Factor (Continuous); 1.0 with VFD; 50 Hz 1.0 Service Factor (Continuous)

• Insulation: Class F

• Temperature Rise: Class B

• NEMA Design C: Torques Equal or Greater Than 200% Starting Torque / 250% Breakdown Torque

• Construction: Cast Iron Frame; End Brackets; Main Conduit Box; Rolled Steel Fan Cover⁽⁷⁾

• Grounding Terminal: Inside Main Conduit Box⁽⁸⁾

• Conduit Box: Oversized Main Conduit Box Rotatable in 90 Degree Increments - F1 Mounted

• Ambient Temperature: Designed for < 40°C

• Elevation: Designed for < 3300 ft. Elevation

• Rotation: Bi-Directional

• Shaft: High Strength 4140 AISI Steel

• Rotor Construction: Aluminum Die Cast Squirrel Cage

• Paint System: Phenolic Rust Proof Base Plus Polyurethane Top Coat

• Paint Color: Dark Gray - Munsell 7.5 BG 3.5/0.5

• Bearings: High Quality Ball (or Roller) Bearings Regreasable with Mobil Polyrex™ EM Grease

• Fittings: Automatic Grease Discharge Fittings

• Gamma (Axial Face) Seal on Both Ends for F# 140T - 400T

• Labyrinth Type Metal Flinger on Both Ends for F# 440T and Larger

• Cast Iron Inner and Outer Bearing Caps for F# 320T and Larger

• Nameplate: Stainless Steel Nameplate

• VFD: Suitable for Inverter Duty (PWM - Pulse Width Modulation) per NEMA MG-1 Part 30(4 and 5)

• Inverter Duty Speed Range: 20:1 Variable Torque / 10:1 Constant Torque (350 HP and Larger are 3:1 Constant Torque)

• 12 Leads for 125 HP and Smaller

• 6 Leads for 150 HP and Larger

• Protection: Standard With Thermistors (PTC 140°C) 1 per Phase

• Locknut and Washer on NDE for Vertical Shaft Down Applications on F# 440 and Larger

• Drain Holes / Plugs on Both End Brackets for Vertical Applications

• Threaded One Way Breather Drains for Horizontal Mount Applications

• Precautions should be taken to eliminate or reduce shaft currents that may be imposed on the motor by the VFD as stated per NEMA MG-1.

• ⁽⁷⁾ F# 5000 and with Larger with Pressed Steel Plate Main Conduit Box.

• ⁽⁸⁾ Additional Foot Grounding Provision for F# 440 and Larger.


Note: Stock catalog image shown. Actual motor may differ.